Comments on: Mini Flashing Guide for DIR-300

By: Problema flasheo Dlink DIR-300 - Foros de CHW

Problema flasheo Dlink DIR-300 - Foros de CHW — Tue, 17 Nov 2009 02:17:46 +0000

[...] dir -300 si me equivocaba podia volver el punto 1 hacer y volver al redbot y empezar todo denuevo Mini Flashing Guide for DIR-300 | shadowandy – my life stories como veia si podria volver a reflashear con el programa putty o con cmd con un ping -t ala ip [...]

By: shadowandy

shadowandy — Sun, 04 Jan 2009 03:15:07 +0000

buddsn,

from what I see from your ps. The web interface is already running. Make sure that your proxy settings allow local access.

By: buddsn

buddsn — Sat, 03 Jan 2009 18:09:20 +0000

thx for the nice manuel but i have a problem

i dont have an webinterface after flashing my dir-300 i can connect with putty but there is no webinterface when i go with my browser on 192.168.1.1 there is only an empty white page nothing else

but the ps show me that:
root@DD-WRT:~# ps
PID USER VSZ STAT COMMAND
1 root 2404 S /sbin/init noinitrd
2 root 0 SW< [kthreadd]
3 root 0 SW< [ksoftirqd/0]
4 root 0 SW< [events/0]
5 root 0 SW< [khelper]
6 root 0 SW< [kblockd/0]
7 root 0 SW [pdflush]
8 root 0 SW [pdflush]
9 root 0 SW< [kswapd0]
10 root 0 SW< [aio/0]
11 root 0 SW< [mtdblockd]
18 root 2428 S /sbin/watchdog
82 root 2400 S resetbutton
158 root 1308 S /usr/sbin/telnetd
160 root 3672 S httpd -p 80
164 root 1088 S dnsmasq –conf-file=/tmp/dnsmasq.conf
262 root 2424 S /sbin/wland
265 root 976 S cron
270 root 968 S udhcpc -i vlan2 -p /var/run/udhcpc.pid -s /tmp/udhcpc
274 root 2364 S ttraff
327 root 0 Z [rflow.startup]
368 root 1324 S -sh
370 root 1308 R ps

what can i do to get an webinterface ?

By: shadowandy

shadowandy — Sun, 28 Dec 2008 03:11:47 +0000

cirkit,

I am not pretty sure of the exact problem as I do not own the latest hardware revision of the DIR-300. If you have a serial-to-ttl cable. You can attach it to the DIR-300 and monitor if any error messages have been thrown out in the console.

By: cirkit

cirkit — Fri, 26 Dec 2008 21:58:57 +0000

Hi! shadowandy, i have successfully flashed my second Dir-300 after flasing the first before 4 months. But I have one query… This time after issuing the create linux command ,Putty lost connection, I waited for some time and rebooted the router, tried to telnet to 192.168.1.1 9000 it took approx 1 min but i managed to get the DD-Wrt prompt and then i continued with the remaining steps and successfully gained access to dd-wrt v24. Earlier Brian also faced such a problem, I too had ensured that the never exit was checked in Putty. What may be the exact reason..??

By: eldiablo

eldiablo — Thu, 25 Dec 2008 03:51:01 +0000

Thanks for the guide..i upgraded from stock fw to v24 (05/20/08) – not sure rc5 or rc7..how can i upgrade to the latest version – v24 sp1 from my current dd-wrt fw? the version i’m using hangs daily…

By: taurius1

taurius1 — Wed, 24 Dec 2008 06:35:09 +0000

Thanks for the wonderful guide. I managed to get it done on my own, within 2 minutes. I had some problems, but nothing that wasn’t already resolved in other people’s queries on this page.

^_^

By: shadowandy

shadowandy — Tue, 23 Dec 2008 14:24:03 +0000

t3rmig,

Just power off the device and start all over again.

By: shadowandy

shadowandy — Tue, 23 Dec 2008 14:23:19 +0000

hkechung,

Make sure the set has been properly flashed before rebooting/resetting the device.

By: t3rmig

t3rmig — Mon, 22 Dec 2008 12:06:04 +0000

Hi everybody,
I think i’ve bricked my router after mistakenly put the DD-WRT> load -r -b %{FREEMEMLO} ap61.rom<– which i’ve replaced with ap61.ram.
So anybody knows how to recover it back?
One more thing, where to get the ap61.rom since I cannot see it in the download page.

Thanks