MLDonkey 2.9.3 for DNS-323, DNS-313, CH3SNAS, …

MLdonkey 2.9.3 has been released on the 19th of January 2008. Compiled it a few days back, recompiled it every now and then. Noticed that the size of the binary has increased quite a bit.

Didn’t see any significant changes in the changelog for MLDonkey 2.9.3. I am offering the MLDonkey client in three flavors again – real simple edition, normal, and full. The procedures for setting up the real simple edition is exactly the same as 2.9.2. Simply extract the files of the real simple edition onto your Volume_1 and reboot.

Head over to MLDonkey for DNS-323 to grab your copy of MLDonkey 2.9.3 for your DNS-323, DNS-313, CH3SNAS, etc.

16 thoughts on “MLDonkey 2.9.3 for DNS-323, DNS-313, CH3SNAS, …

  • February 1, 2008 at 6:11 pm
    Permalink

    Thanks a lot, you rock!

  • February 1, 2008 at 9:04 pm
    Permalink

    Thanks alot!

  • February 2, 2008 at 2:20 am
    Permalink

    Thanx, much appreciated!

  • February 8, 2008 at 1:42 am
    Permalink

    Hi Andy, how are u? I’m interesting to implement this new release of mldonkey, but i want to install without gdlib because i use only sancho…is it possible? Thanks again:)

  • February 8, 2008 at 11:42 am
    Permalink

    Cipo_Italy,

    Hi! It has been fine except for the number of project deadlines. Well, the gdlib won’t really affect your sancho implementation. You have concerns regarding the presence of gdlib?

  • February 13, 2008 at 6:32 pm
    Permalink

    Hi Shadowandy,
    I was running 2.9.2 and downloaded and extracted 2.9.3 per your instructions. As the files extracted and over write the 2.9.2 files, it stalled because the “torrents” directory can’t be accessed. Any ideas?

  • March 7, 2008 at 3:31 pm
    Permalink

    Hi, how can you shut down MLdonkey?

    Thanks.

  • March 7, 2008 at 11:48 pm
    Permalink

    Hi,

    Just installed mldonkey, managed to search using edonkey for some files, managed to put in some torrents to download. However, after the initial few minutes, there is no further download/upload activity. Is there anyway I can troubleshoot this? Or is there anything I can do to test to make sure that my installation is working?

    Thanks!!

  • May 14, 2008 at 9:26 pm
    Permalink

    hi, I added a new HD in my 323, and re-format both 2 HD to RAID 1, of course, before I added the HD, I backed up all files to another place. After the format was done, I moved all previours files to 323. But the mldonkey is not running. I tried to manual re-start it, but still fail; here is the result:

    2008/05/14 21:11:26 [cO] Starting MLDonkey 2.9.3 …
    2008/05/14 21:11:26 [cO] Language EN, locale UTF-8, ulimit for open files 1024
    2008/05/14 21:11:26 [cO] MLDonkey is working in /.mldonkey

    2008/05/14 21:11:26 [cO] creating new MLDonkey base directory in /.mldonkey

    2008/05/14 21:11:26 [cO] loaded language resource file
    2008/05/14 21:11:26 [DNS] Resolving [DataBank] …
    Segmentation fault
    / #

  • May 15, 2008 at 10:47 pm
    Permalink

    ricthoo,

    Perhaps you can check the load of the DNS-323. Otherwise you could try to limit the amount of files you download. MLDonkey is pretty stressful on the CPU.

  • May 15, 2008 at 10:49 pm
    Permalink

    lotpeter,

    For segmentation faults. You have to remove the directory /mnt/HD_a2/mldonkey . That is the only solution I have currently.

  • June 3, 2008 at 3:03 pm
    Permalink

    I’ve noticed mldonkey does not let the disks to spin down even if there are no active torrents.

    Is there anything I can do for this other than kill core after download completed?

  • June 4, 2008 at 7:18 am
    Permalink

    adam,

    The mldonkey scans a particular directory every fixed interval to add .torrent files to download. Run thru the settings and try disabling the scanning to see if it works.

Comments are closed.